Why have a made to measure roller shutter?
Because a window almost never matches a catalogue size: a made to measure roller shutter fills the opening exactly, with no gaps at the sides and no curtain rubbing. In Pays de Caux longhouses, brick townhouses or 1970s detached homes, openings vary from one frontage to the next, and sometimes from one window to its neighbour.
A shutter that is too narrow lets light and wind through and is easier to lift. One that is too wide binds in its guide rails and wears the motor or strap. Made to measure simply means a shutter that closes properly, for a long time.
At DEPANN'Rideaux, the person who measures is the person who fits, and the one you call if anything goes wrong. Each shutter is made to measure to the dimensions taken by the technician, then fitted by him.
How is a window measured up?
The technician measures every window himself, on site: nothing is ordered on measurements given over the phone.
- 1Width and heightTaken at several points in the reveal, to spot an out-of-square opening, common in older buildings.
- 2Fitting typeOn the wall, under the lintel, on the window frame or in an existing box: the depth of the reveal and the space above the window decide.
- 3ObstaclesWindow handles, projecting sills, gutters, downpipes, outdoor lighting.
- 4PowerWhether there is a power supply near the window, or how the frontage is exposed for a solar version.
Which slats should you choose for a made to measure shutter?
The choice is between PVC and aluminium, depending on the window size and its exposure.
| Slats | Strengths | Good to know |
|---|---|---|
| PVC | Light, insulating, does not rust | For narrower windows only; dark colours not advised in full sun |
| Double-walled aluminium with insulating foam | Stiff, insulating, wide choice of colours | The most common choice for medium and large openings |
| Extruded aluminium | More resistant to break-in attempts | Heavier: often paired with a motor |
Some slats can be perforated to let a little air and light through with the shutter down. Available profiles depend on the supplier and are stated on the quote.
Which guide rails and which box?
The guide rails steer the curtain and the box protects the rolled-up shutter: they are sized at the same time as the slats.
Guide rails
Aluminium, lined with brush or rubber seals that reduce the noise of the curtain in the wind. Their depth follows the width of the shutter.
On the coast: choose powder-coated rails and stainless steel screws.The box
Visible (bevelled, quarter-round, square) for retrofits, or hidden in the wall in new builds. Its size depends on the height of the rolled-up curtain.
To check: the space above the window.Bottom slat and locks
The bottom slat has a seal that closes against the sill. Automatic locks can stop the curtain being lifted.
Useful: on the ground floor and on windy frontages.The choice between a visible and a built-in box is explained on the retrofit roller shutter and built-in roller shutter pages.
Can you choose the colour of your roller shutters?
Yes: slats, guide rails and box come in a range of colours, often from the RAL chart, and can be different colours. The box is usually matched to the window frames and the curtain to the frontage or the old hinged shutters.
In a protected area, near a listed monument or in a block of flats, the colour may be restricted: check with your town hall’s planning department or your managing agent before confirming. The chart of available colours is shown to you during the site survey.
Which operation should you choose for a made to measure shutter?
Operation is decided when ordering, as it changes the roller tube, the box and sometimes the slats.
- Manual, by strap or crank: simple, no electricity. See manual window shutters.
- Mains electric, tube motor with wall or radio control. See electric window shutters.
- Solar, with no cable to the fuse board. See the solar roller shutter.
A manual shutter in good condition can also be upgraded later: see window shutter motorisation.
How long does it take and how is the price of a made to measure shutter set?
The manufacturing and fitting lead time and the price are written on the quote, given to you after measuring on site. The site survey is free and with no obligation: nothing is ordered without your agreement.
The price depends on five things: the size of each window, the slat material, the type and shape of the box, the operation and the options (locks, different colours, central control). The quote details each shutter, window by window.
Where do we fit made to measure roller shutters?
All over Normandy, including around Rouen, Caen, Le Havre and Dieppe, setting out from Gruchet-le-Valasse. The fitting process is described on the window shutter installation page, and window shutter maintenance extends their life. Every model is on the window roller shutters page. For a shop, the same know-how applies to made to measure shop shutters.





