The key won’t turn: what can you do without making it worse?
A lock that resists often ends up breaking the key if you keep at it. These simple steps are sometimes enough, and protect the cylinder in every case.
- Don’t force the key. A bent or cracked key can snap inside the cylinder.
- Check the key. Is it the right one, is it worn or bent? Try the spare if you have one.
- Take the load off the lock. On a manual shutter, press lightly on the bottom slat while turning: a bolt under strain can jam the mechanism.
- Use a lubricant made for locks if the cylinder is simply stiff, never cooking oil or thick grease.
- Key broken in the lock? Don’t try to pull it out with pliers: you would push the piece further in. Call +33 7 68 20 39 55.
What types of lock are fitted to a roller shutter?
A roller shutter is locked by a central lock, by side bolts, or by both; an electric shutter is also operated by a key switch. Identifying your shutter’s system helps us bring the right part.
Central lock
Built into the bottom slat, in the middle of the shutter. When you turn the key, it drives rods or bolts that engage in the guide rails or in the ground.
Sign of wear: the key catches, does not turn fully, the bolt no longer comes out all the way.Side bolts
Placed at each end of the bottom slat, they lock the curtain into the guide rails. Some shutters have two, operated separately, often with padlocks.
Sign of wear: the bolt no longer goes into its slot, the shutter can be lifted when closed.Key switch
On an electric shutter, this is the wall unit that controls raising and lowering. Its cylinder wears and clogs just like a lock’s.
Sign of wear: you have to turn it several times, or the control no longer responds. See remotes and control boxes.Lost or broken key: does the whole lock need changing?
No, in most cases only the cylinder needs replacing. A key broken in the lock is removed with dedicated tools; if the cylinder is undamaged, a new key is enough. A lost key, on the other hand, is a security issue: if it may have been found or stolen, it is better to change the cylinder so that the old key no longer works.
For a spare key, it all depends on the cylinder. Common keys are easily copied; cylinders with restricted keys usually require the ownership card supplied at purchase. Keep it with your business papers, not on the premises.
What should you do after an attempted break-in on the lock?
First secure the premises, then replace the damaged lock and check the whole bottom of the shutter. A lock forced with a crowbar or a drill rarely leaves the bottom slat, the bolts and the guide rails intact. The technician checks everything and gives you an itemised invoice, with photos of the damage, useful for your insurance claim.
What you need to do depends on your insurance policy: ask your insurer about reporting to the police and claim deadlines. For a night call-out after a burglary, see the page on a shutter forced after a break-in.
How can you make your shutter more secure?
Upgrading security means adding locking points and making the lock harder to pick or rip out. The options are chosen on site, depending on the shutter and how exposed the shop is:
- A tougher cylinder, with a key protected against copying.
- Extra side bolts to lock the curtain at both ends.
- Floor locking, which stops the bottom slat from being levered up.
- A reinforced bottom slat when the current one has been bent.
- Lock protection with a cover or an anti-drill plate.
This work is carried out on a written quote, given to you before any work starts. Some insurers require a specific level of security for business premises: check your policy before choosing. A bottom slat that needs replacing is covered on the slat replacement page.
How do you look after the cylinder of a roller shutter lock?
A cylinder is looked after by regularly applying a lubricant made for locks and by protecting it from water and dust. Exposed to rain, salt by the sea or dust from nearby building work, a roller shutter lock gradually seizes up.
- Spray the product into the keyway, then work the key several times.
- Avoid household oil and thick grease, which pick up dust.
- Replace a worn key before it damages the cylinder.
- Tell us about a key that sticks: that is the time to repair, before it breaks.
The bolts, rods and bottom slat are checked at every visit under our maintenance contract. If your shutter won’t open at all, the guide why is my roller shutter stuck helps you tell a lock fault from a mechanical fault.
How much does work on a shutter lock cost?
The price depends on the part to change and the cylinder model.
The technician gives you the price on site, after the diagnosis and before any work starts: nothing is done without your agreement, and if you decline the work after the diagnosis, only the call-out is charged. On the phone, your description and, if needed, a photo of the cylinder help the technician bring the right part; itemised invoice at the end. How the price of a call-out is set.
What makes the price vary?
- The type of fault: freeing a cylinder or removing a broken key takes less time than replacing a complete lock.
- The cylinder model: a standard cylinder is often in the van, a restricted-key cylinder sometimes has to be ordered.
- The number of locking points: central lock only, or side bolts or floor locking as well.
- Damage around the lock: after a break-in, the bottom slat or the guide rails may also need work.
- When the work is done: a lock change booked during the day avoids the surcharge that applies at night, on Sundays and on bank holidays.
Where do we work on shutter locks?
Throughout Normandy, day and night, including:
All our other repairs are on the roller shutter repair page; for a shutter that is too heavy or rubs, see axle, springs and guide rails.
