Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Technicians available now · 24/7

Roller shutter motor not working? We repair it or replace it.

A roller shutter motor that is not working most often has a dead capacitor, a stuck electromagnetic brake, a tripped thermal cut-out or limit switches out of adjustment. DEPANN'Rideaux repairs central and tube motors of all makes, 24/7 in Normandy: the technician gives you the price on site, after the diagnosis and before any work starts.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

Request a call-out

Quick reply, 7 days a week
What do you need?
Add a photo (optional)

Your details stay confidential.

The motor no longer responds: what can you check without taking any risks?

Before you call, four simple checks are sometimes enough to get the motor going again. If not, they help the technician pinpoint the fault.

  1. Is the shutter’s circuit breaker switched on? A trip at the fuse board looks just like a motor failure.
  2. Do the controls work? Remote batteries, key switch, an emergency stop button left pressed in.
  3. Has the motor overheated? After repeated operation, the thermal cut-out switches it off. Let it cool down without persisting.
  4. What can you hear? A click, a hum or total silence: make a note of it, it is the most useful clue over the phone.
Do not take the shutter box apart and do not touch the 230 V wiring. The motor is connected to the axle that carries the full weight of the curtain, and any springs are under tension.

What symptoms show that a roller shutter motor is failing?

The symptom almost always points to the part at fault. Describe it to the technician: he will know which part to bring.

What you noticeLikely cause
The motor does not react at all, no soundPower supply, thermal cut-out, control board or receiver
A click each time you press the control, then nothingElectromagnetic brake not releasing, or control relay
The motor hums or runs with no effect, the shutter does not moveDead capacitor, worn gearbox or broken link with the axle
The shutter stops partwayLimit switches out of adjustment, thermal cut-out, obstacle safety device
The motor overheats then cuts outOperations too close together, curtain rubbing, undersized motor
Squeaking, knocking or vibrationWorn bearing, gearbox or motor mounting

What causes a roller shutter motor to fail?

Six causes account for the vast majority of motor failures. Several can be repaired without changing the motor.

Dead capacitor

The capacitor helps a single-phase motor to start. When it wears out, the motor hums without any power. It is a small part, often changed on site.

Sign: humming with no movement, difficulty starting.

Electromagnetic brake

It holds the curtain when stopped. If it sticks or its coil fails, the motor can no longer turn, or the shutter slips.

Sign: a sharp click, or a shutter that comes back down on its own.

Thermal cut-out

It switches off a motor that is overheating. Now and then, this is normal; if it happens often, it points to a curtain that is straining or a tired motor.

Sign: the motor starts again after cooling down, then cuts out again.

Limit switches out of adjustment

They tell the motor where to stop at the top and bottom. Out of adjustment, they stop it too early or let it strain against the end stop. A possible result: a shutter stuck open.

Sign: stopping at an unusual height.

Control board or radio receiver

Damp, a power surge or wear: the command no longer reaches the motor, even though the motor itself is sound.

Sign: the remote no longer works but the key switch does. See remote or control box not working.

Power supply

A circuit breaker, a fuse, a loose terminal or a cable damaged by a knock: the motor is no longer getting any current.

Sign: no sound, whichever control you use.

Central or tube motor: what difference does it make to the repair?

The type of motor mainly affects access and which parts can be repaired. The technician will ask you which one you have, or recognise it from a photo.

  • Central motor: fitted in the middle of the axle, it is found on wide shutters. It is easy to reach, its parts (capacitor, brake, limit switches) can be changed separately, and it often has a manual override by winch or crank.
  • Tube motor: housed inside the axle, compact and discreet. Repairing it means taking it out of the axle, and it is often replaced as a whole unit when it fails.

To find out more about this equipment, see our electric roller shutter page.

Should you repair or replace your shutter’s motor?

We repair when the fault affects a replaceable part on a sound motor; we replace when the motor itself is worn or unsuitable. The technician sets out both options and their prices before starting.

  • Repair: capacitor, brake, limit switches, control board or receiver. This is our roller shutter motor repair service.
  • Replacement: a burnt-out winding, a worn gearbox, a motor that constantly overheats or is too weak for the weight of the curtain. This is our motor replacement service, with a model suited to the size of your shutter. A new motor comes with a warranty of 2 years on the motor (manufacturer's warranty) and 1 year on fitting.

How much does a roller shutter motor repair cost?

The price depends on the part at fault and on whether it is repaired or replaced; the technician gives it to you on site, once the diagnosis is done and before touching the motor.

Price given on site, before any work starts. On the phone, describe the symptom (click, hum, no response): the technician narrows down the likely part and brings it. On site, he makes the diagnosis, gives you the price and only goes ahead with your agreement; if you decline the work after the diagnosis, only the call-out is charged. You receive a detailed invoice at the end. How the price of a repair is set.

What makes the price vary?

  • The faulty part: a capacitor or a limit switch adjustment costs much less than a brake, a control board or a complete motor.
  • Repair or replace: a new motor, central or tube, is chosen according to the weight and width of the curtain.
  • The type of motor: a tube motor has to be taken out of the axle, whereas a central motor can be reached directly.
  • The time of day: a call-out at night, on a Sunday or on a bank holiday carries a surcharge.
  • The distance: the call-out charge depends on the distance from our base in Gruchet-le-Valasse and is given to you together with the price of the job.

Can you open the shutter when the motor has failed?

Yes, if your motor has a manual override and the instructions explain how to use it: this is the case with many central motors. The winch or crank then lets you raise or lower the curtain without power, slowly and without forcing it.

If the crank resists or turns without catching, or if you have no manual override, stop and call us: a shutter with a damaged axle or spring can suddenly break free. Our guide to opening a roller shutter manually explains what you can do. If the shutter stays down, see also shutter stuck closed.

Where do we repair roller shutter motors?

Across Normandy, 24/7, with the common parts in the van, including:

A motor lasts longer with a well-guided curtain and properly adjusted limit switches. A maintenance contract means they are checked regularly. You will find every emergency on our emergency roller shutter repair in Normandy page.

Google reviews

What our customers say

Reviews are shown in their original language (French).

5.0
★★★★★
“Excellent” · 5 Google reviews
★★★★★
« Intervention rapide et très professionnelle. Dépanneur efficace, ponctuel et honnête sur les tarifs. Porte sectionnelle réparée rapidement et proprement. »
Khalid R.Google review
★★★★★
« Dépannage rapide ! Bon prix, très aimable et accessible. »
Emilie R.Google review
★★★★★
« Le monsieur est un professionnel, le travail est minutieux, je vous le recommande. »
Hassan I.Google review

All customer reviews See our Google profile

Frequently asked questions

Shutter motor failure: your questions

Why does my shutter’s motor run without the shutter moving?

Most often, the capacitor is worn or the link between the motor and the axle has broken. Stop pressing the control: persisting only makes the motor overheat, with no result.

Do you change the motor the same day?

It is possible: the van carries central motors in common power ratings, as well as common parts: capacitors, limit switches, universal remotes and receivers, cylinders, galvanised slats and common spring boxes. If your shutter needs another model, allow 2 to 5 working days for the motor to be delivered; in the meantime the shutter is opened, or closed and secured.

Do you repair motors of all makes?

Yes, both central and tube motors, whatever the make of the motor or the shutter.

My motor often overheats and cuts out: is it serious?

It is a warning sign: the thermal cut-out is protecting you, but the motor is straining. A curtain that rubs or an undersized motor should be checked before it fails completely.

Can a shutter that has become manual after a breakdown be motorised again?

Yes. If your shutter has been operated by hand since a breakdown, we can fit a suitable motor. See motorising a manual shutter.

Your shutter’s motor no longer responds?

Describe the symptom to a technician: he narrows down the part, comes with what is needed and gives you the price on site, before any work.