A slat is damaged: how do you limit the damage in the meantime?
A bent slat works against its neighbours every time the shutter moves. These precautions stop one slat to replace from turning into five.
- Use the shutter as little as possible. If it rubs or strains, leave it in the position that keeps your premises safest.
- Don’t hammer the slat straight. A hammer blow distorts the interlocking joint and makes the slat unusable.
- Locate the slat in question. Count its position from the bottom: it helps us prepare the job.
- Photograph it close up and from a distance, then send the photos to +33 7 68 20 39 55 or through the form.
When does a roller shutter slat need replacing?
A slat needs replacing as soon as it hampers rolling up, no longer protects the premises or damages the slats next to it. A small dent with no effect can wait; a folded slat that catches in the guide rail cannot. The most common situations:
- A vehicle or trolley impact: slat pushed in, joint opened, curtain out of line.
- An attempted break-in: slats bent with a crowbar, often near the lock or at the bottom of the shutter.
- Corrosion: rust eating through old slats or slats exposed to sea spray.
- Worn joints: the slats work loose, the curtain ripples and eventually comes out of the guide rails.
- A crushed bottom slat: the shutter no longer closes flat and the bolts no longer engage.
If the shutter is stuck because of a slat, it is an emergency first: see the page on bent or broken slats, which explains how we free the shutter and secure the premises before the repair.
How do you identify your shutter’s slat profile?
A slat is identified by its visible height (the pitch), its thickness, the shape of its joint, any perforation and its finish. All of these must match: an “almost identical” slat will not interlock, or will stand out at first glance.
Solid slat
The most common profile on shops. It hides the shop window completely and keeps out the weather. Several pitches and thicknesses exist depending on the width of the shutter.
Note down: height of one slat, shape of the fold, single or double wall. See solid slat shutters.Micro-perforated slat
Pierced with small, regular holes that let you see the shop window and let air through. The new slat must have exactly the same perforation pattern.
Note down: size and spacing of the holes, perforated or solid area. See perforated shutters.Galvanised or lacquered
Galvanised steel keeps its grey metal look. A lacquered slat has a specific colour, which has to match the rest of the curtain, sometimes faded by the sun.
Note down: the colour reference if you have it, otherwise a photo in daylight.There is no need to take anything apart to help us: a photo from the front, a photo of the slat edge visible in the guide rail and the rough width of the shutter are often enough to prepare the right slat.
Can just part of the curtain be replaced?
Yes: it is in fact the most common case, because the slats of a curtain interlock with each other and can be replaced individually. Roller shutter slat replacement goes like this:
- 1Making safeThe shutter is set in the right position and held still, so we can work with no risk of the curtain dropping.
- 2Removing the damaged slatsThe technician frees the section concerned and slides the damaged slats out of their joints.
- 3Fitting new slatsThe new slats, in the same profile and with their end caps, are threaded in, then the curtain goes back into its guide rails.
- 4Checking the guide rails and adjustingThe knock that bent a slat has often marked a guide rail: it is checked, straightened or replaced if needed.
- 5TestingSeveral full openings and closings to check that the curtain rolls up straight with no rubbing.
When a large part of the curtain is rusted or the profile is no longer made, we tell you straight: replacing the whole curtain may then cost less than a string of repairs.
Why does the bottom slat need particular attention?
Because the bottom slat, at the foot of the curtain, takes the contact with the ground at every closing and often carries the lock and the bolts. It is thicker or reinforced compared with the other slats. Crushed or bent, it leaves a gap under the shutter, prevents locking and makes a break-in easier.
Replacing it therefore means refitting the lock or the bolts: we use the visit to check their condition and replace them if necessary. Details are on our roller shutter locks page.
How long does it take if the slat has to be ordered?
Our vans carry the common parts (capacitors, limit switches, universal remotes and receivers, cylinders, galvanised slats and common spring boxes); rarer profiles or slats lacquered in a specific colour have to be ordered. Average supply time: 3 to 5 working days for a standard slat, 2 to 3 weeks for a lacquered or special slat.
In the meantime, your premises are not left unprotected: on the first visit the shutter is made to close again or secured, then we come back to fit the new slats as soon as they arrive.
What does it cost to change one or more slats?
The price depends on the slat profile, the width of the shutter and the number of slats to change.
Price given on site by the technician, after checking the slats and guide rails and before any work starts: nothing is done without your agreement. Your photos of the damaged slats help us prepare the right profile; if you decline the work after the diagnosis, only the call-out is charged. Itemised invoice at the end. How the price of a repair is set.
What makes the price vary?
- The slat profile: a micro-perforated slat or a reinforced bottom slat is a more technical part than a standard solid slat.
- The number of slats to change: each extra slat fitted during the same visit costs much less than the first.
- The finish: a slat lacquered in a specific colour is made to order, whereas a common galvanised slat is often in the van.
- The condition of the guide rails and the lock: if the knock has also marked a guide rail or the bottom slat carrying the lock, these parts are added to the quote.
- When the work is done: a replacement booked during the day avoids the surcharge that applies at night, on Sundays and on bank holidays.
When too many slats are affected, a new curtain may become the more sensible option: the guide to the cost of a new roller shutter explains what drives its price.
Where do we replace roller shutter slats?
Everywhere in Normandy, with particular attention to coastal towns, where salty air speeds up slat corrosion:
Our other mechanical repairs (springs, axle, guide rails, lock) are covered on the roller shutter repair page. If your guide rails are bent too, see axle, springs and guide rails.
