Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Technicians available now · 24/7

Roller shutter remote not working? We get the controls working again.

When a roller shutter remote stops working, the cause is often simple: a flat battery, a transmitter that has lost its pairing or a faulty radio receiver. If the key switch does not respond either, the power supply, wiring or motor need checking. DEPANN'Rideaux diagnoses the whole control circuit, 24/7 in Normandy: the technician gives you the price on site, after the diagnosis and before any work starts.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

Request a call-out

Quick reply, 7 days a week
What do you need?
Add a photo (optional)

Your details stay confidential.

The shutter no longer responds to the remote: what can you check yourself?

Four checks without tools are often enough to tell whether the fault lies with the transmitter, the receiver or the rest of the installation.

  1. Look at the light on the remote. If it no longer comes on or is dim, change the battery: its reference is printed on it.
  2. Try another control. A second transmitter, the key switch or an inside button: if one of them works, the motor is not to blame.
  3. Move closer to the shutter. A remote that only works a few steps away points to a weak battery or poor reception.
  4. Check the power supply. Shutter circuit breaker switched on, emergency stop button released, no power cut in the street.
Do not open the control box, the receiver or the key switch. They are connected to the 230 V supply and a wiring mistake can also damage the motor.

Why has my roller shutter remote stopped working?

A roller shutter remote stops working for one of five reasons, from the most ordinary to the most technical. Testing the other control, described above, already rules out several of them.

Flat battery

This is the most common cause. The range shrinks first, then the transmitter no longer triggers anything.

Sign: a dim light or none, you have to press several times.

Range disrupted

The receiver’s aerial has been moved or damaged, new metal fittings, radio equipment installed nearby: the signal does not get through properly.

Sign: it works at the foot of the shutter, not from the pavement opposite.

Transmitter not recognised

Code erased from the receiver, a badly programmed duplicate or a remote on another frequency: the receiver ignores the command.

Sign: the light is normal, the shutter does not move, another remote works.

Faulty radio receiver

A power surge during a storm, damp in the box, a worn component: no transmitter is picked up any more.

Sign: every remote is dead, the key switch works.

Damaged remote

Dropped, got wet, a button pushed in: the transmitter itself has failed.

Sign: new battery, no light, or a light that stays on permanently.

Neither the remote nor the key switch works: where is the fault?

If no control responds, the fault is no longer in the remote but in the power supply, the wiring, the control board or the motor. This table helps you describe the situation over the phone, so the technician arrives with the right parts.

What you noticeLikely source
The remote does nothing, the key switch worksTransmitter or radio receiver
No control responds, no soundCircuit breaker, fuse, emergency stop, wiring or control board
The shutter responds intermittentlyCorroded switch, loose connection in a cable
The shutter goes up but no longer comes down (or the other way round)Limit switch out of adjustment or faulty switch
The motor hums but the shutter does not moveMotor, brake or capacitor: see motor failure

If the fault has left the shutter stuck closed or open, see also shutter stuck closed.

Remote lost or stolen: what should you do to keep the premises secure?

Have its code erased from the receiver as soon as possible: as long as it is stored there, whoever finds it can open your shutter. Buying a new remote is not enough, as the old one stays active.

The technician clears the receiver’s memory, then reprograms only the transmitters you are keeping. It is also a good time to take stock of remotes handed to former staff or contractors. On an older fixed-code installation, we can offer you a rolling-code receiver, which is much harder to copy. If the loss goes with a theft or intrusion, see our page roller shutter forced after a break-in.

Can you reprogram a shutter remote yourself?

It is possible on some models, starting from a remote that is already recognised and following the manufacturer’s instructions. In other cases, pairing is done with the button on the receiver, which sits in a live box: that is a job for a technician.

Be careful with duplicates bought online: a remote must use the same frequency and the same protocol as the receiver. Before ordering one, send us a photo of the original transmitter and of the receiver’s label.

Key switch or control box not working: repair or replace?

A faulty key switch is usually replaced: it is exposed to rain, frost and attempts to force it, and its internal mechanism is hard to repair. A key that turns without catching, a seized cylinder or a box that has been torn off are the typical signs.

When replacing it, we check the cable connecting the box to the motor, which is often damaged at the same spot. Depending on how you use it, a keypad or a better-protected box can replace the old one. All the options are set out on our roller shutter remotes and control boxes page.

How much does it cost to repair a roller shutter’s controls?

The price depends on the item to be replaced and the make of the receiver.

Price given on site, before any work starts. On the phone, give the make of the motor or receiver if you know it: the technician brings the right parts. On site, he carries out the diagnosis, gives you the price and does nothing without your agreement; if you decline the work after the diagnosis, only the call-out is charged. How the price of a repair is set.

What makes the price vary?

  • The faulty item: programming an existing transmitter, supplying a new remote, changing the radio receiver, the key switch or the push-button control box are different jobs.
  • Compatibility with your receiver: if the original transmitter is no longer made, the receiver sometimes has to be replaced before new remotes can be added.
  • A lost or stolen transmitter: the receiver’s memory then has to be cleared and every remote you keep reprogrammed.
  • The condition of the wiring: a damaged cable between the box and the motor is repaired at the same time as the switch.
  • The time of day and the distance: nights, Sundays and bank holidays carry a surcharge, and the call-out charge depends on the distance from our base in Gruchet-le-Valasse.

If no control responds at all, the fault may lie elsewhere: read our guide why is my roller shutter stuck.

Where do you come out for a faulty remote or control box?

Across Normandy, including Rouen, Évreux, Caen and Lisieux. We work on shutters of all makes, with common receivers and transmitters in the van. Every other emergency is on the emergency roller shutter repair in Normandy page.

Google reviews

What our customers say

Reviews are shown in their original language (French).

5.0
★★★★★
“Excellent” · 5 Google reviews
★★★★★
« Intervention rapide et très professionnelle. Dépanneur efficace, ponctuel et honnête sur les tarifs. Porte sectionnelle réparée rapidement et proprement. »
Khalid R.Google review
★★★★★
« Dépannage rapide ! Bon prix, très aimable et accessible. »
Emilie R.Google review
★★★★★
« Le monsieur est un professionnel, le travail est minutieux, je vous le recommande. »
Hassan I.Google review

All customer reviews See our Google profile

Frequently asked questions

Shutter remotes and control boxes: your questions

Can a power cut upset the remote?

Generally not: when the power comes back, the receiver keeps the stored codes. However, a power surge, during a storm for example, can damage the receiver. If nothing responds after a power cut, check the circuit breaker first.

My shutter opens or closes by itself: is it the remote?

It could be: a button pressed in a pocket, a lost transmitter that is still active, or a faulty receiver. Switch off the shutter at the circuit breaker once the premises are closed, and call us: it is a security issue.

Can you supply a duplicate of my remote?

Yes, if the model is compatible with your receiver. We program it on site and check its range. If the original transmitter is no longer made, we offer you a new receiver and remotes.

How can I open the shutter without the remote?

With the key switch or the inside button, if there is one. Some central motors also have a manual override, to be used only if the instructions say so. Otherwise, a technician comes to open it, on proof that you run or own the premises.

Do you work on all makes of receiver?

Yes. If your receiver will not accept a new remote, we replace it with a model compatible with your motor, with the price given on site before the work.

Your remote no longer controls the shutter?

Tell the technician what responds and what no longer does: he comes with the right parts and gives you the price on site, before any work starts.