A shutter motor that no longer responds does not necessarily need replacing. Very often the fault comes from a wear part, a setting or the controls. The trick is to find it without changing parts at random. This page explains how our technicians work on site. To recognise the symptoms yourself (motor humming, shutter stopping half-way, no sound at all), see our page on shutter motor failure instead.
How does the technician diagnose a faulty shutter motor?
They test each link in a set order, from the power reaching the motor down to the curtain, to isolate the real cause. This method avoids replacing a healthy motor when it is a receiver or a capacitor that has failed.
- 1Power supplyThe technician checks that power is actually reaching the motor: dedicated breaker on the fuse board, supply cable, voltage measured at the terminals. With no power, there is no point going further.
- 2ControlsKey switch, push-button control box, radio receiver, emergency stop button: is the up or down command really reaching the motor? A faulty control can make a motor look dead.
- 3CapacitorOn a single-phase motor, the capacitor helps it start. When it weakens, the motor hums without starting or struggles to get the curtain moving. The technician tests it with a meter.
- 4Electromagnetic brakeIf it no longer releases, the motor strains against it. If it slips, the curtain slides or comes down on its own. The brake’s setting and wear are checked.
- 5Limit switchesMechanical or electronic, they stop the motor at the top and bottom. Out of adjustment, they cut out too early, make the shutter strain against its stop or block one direction of travel.
- 6Thermal protection and windingsIf the motor cuts out after a few operations, the technician looks for why it is overheating, then measures the windings to detect a burnt-out coil.
The diagnosis does not stop at the motor. A curtain rubbing in its guide rails, a bent axle or a worn spring box make the motor work beyond its capacity: it overheats and cuts out to protect itself. In that case, repairing the motor alone is not enough; the axle, springs or guide rails must be dealt with too.
Which motor faults do we repair on site?
Often the fault is fixed by replacing a wear part or redoing a setting, without changing the motor. These are the repairs our technicians commonly carry out during a roller shutter motor repair:
- Replacing the capacitor on single-phase motors.
- Adjusting or replacing the limit switches, then testing up and down.
- Adjusting the electromagnetic brake, or replacing its wear parts where they exist for the model.
- Replacing the radio receiver or the control board, and reprogramming the remotes.
- Changing the key switch or the push-button control box damaged by wear, damp or vandalism.
- Repairing damaged control cables between the control unit and the motor.
- Getting the motor back into service after a thermal cut-out, finding and correcting the cause of the overheating.
Faults that only involve the controls (lost remote, control box to replace, adding a receiver) are covered on our page on remotes and control boxes.
Which parts does the technician carry in the van?
The technician sets off with the common wear parts, which means many faults are fixed in a single visit. Over the phone, they ask you a few questions so the right part is ready before leaving.
- Common parts in stock: capacitors, limit switches, universal remotes and receivers, cylinders, galvanised slats and common spring boxes.
- Motors in stock: central motors in common power ratings.
If a specific part has to be ordered (allow 2 to 5 working days for a motor), we do not leave your premises open: the shutter is closed or made safe the same day, and the permanent repair is scheduled as soon as the part arrives.
Repair or replace the motor: how do you decide?
We repair whenever the repair will be reliable, and only advise replacement when the motor itself is at fault. The technician shows you the faulty part and explains the choice.
| Finding after diagnosis | Our recommendation |
|---|---|
| Worn capacitor, healthy motor | Repair: replace the capacitor |
| Limit switches out of adjustment or faulty | Repair: adjust or replace |
| Brake slipping or no longer releasing | Repair if parts exist, otherwise replacement |
| Faulty receiver or control board | Repair: replace the control component |
| Burnt-out windings | Motor replacement in most cases |
| Worn gearbox, grinding, knocking | Motor replacement |
| Old motor, parts unavailable, repeated faults | Replacement with a motor sized for the curtain |
General recommendations: the final decision depends on the model, its age and the condition of the shutter.
When replacement is necessary, choosing the new motor, reconnecting the controls and how the job goes are explained on our page on roller shutter motor replacement.
How much does roller shutter motor repair cost?
The price depends on the part at fault and the time of day.
The technician gives you the price on site, after the diagnosis and before any work starts: nothing is done without your agreement. Over the phone, your description of the symptoms and, if needed, a photo help us bring the right part. Itemised invoice at the end; if you decline the work after the diagnosis, only the call-out is charged. How the price of a call-out is set.
What makes the price vary?
- The part at fault: adjusting limit switches, a capacitor, a radio receiver or a brake do not cost the same or take the same time.
- The type of motor: a tube motor, housed inside the axle, takes longer to reach than a central motor.
- Part availability: a common part is fitted straight away, a model-specific part has to be ordered.
- The cause of overheating: if a worn spring or a bent guide rail is making the motor strain, that mechanical repair is added.
- When the work is done: at night, on Sundays and on bank holidays a surcharge applies to labour; parts cost the same by day and by night.
Where do we repair roller shutter motors?
We repair shutter motors 24/7 across Normandy, including in the following areas:
How do you stop a motor failing again?
Prevention means regular maintenance, which spots brake wear, limit switches drifting out of adjustment or a curtain that strains before it breaks down. In a workplace, it is in fact compulsory for motorised closures. Our guide to looking after your roller shutter explains what you can keep an eye on yourself, and our maintenance contract takes care of the checks. All our motor services are on the roller shutter motors page.
