Shutter stuck: what should you check first?
Start with everything you can check without tools and without touching the mechanism. A good number of “breakdowns” end there.
- Stop trying. Every new command heats up the motor and can make things worse if the curtain is already jammed.
- Is there power? The shutter’s circuit breaker is on, the lights in the premises work, there is no power cut in the street.
- Does the control respond? Remote control batteries, another remote, the key switch, an emergency stop button left pressed in.
- Is something in the way? An object on the ground under the bottom slat, a bin or A-board against the guide rails, frost on the threshold in winter.
- Look without forcing: the position of the shutter, crooked slats, the noise of the motor. Make a note and take a photo.
Where is your roller shutter stuck: at the bottom, at the top or halfway?
The position where the shutter stopped is the first clue: it rules out several causes straight away. Then combine it with whether or not there is a noise to find the most likely explanation.
Stuck at the bottom (the shop cannot open)
- No noise, no movement: no power, a control that has stopped working (remote, receiver, key switch), emergency stop pressed in, or the motor’s thermal cut-out triggered after repeated attempts.
- The motor hums but the shutter does not rise: faulty capacitor, electromagnetic brake not releasing, a bolt still engaged, bottom slat frozen to the ground or curtain jammed in a guide rail.
- Manual shutter impossible to lift: lock or side bolts still closed, broken spring (the curtain suddenly feels very heavy), bent slat catching.
See the detailed solution on our page roller shutter stuck closed.
Stuck at the top (the shop cannot close)
- No noise: the same electrical causes as above, or a badly adjusted lower limit switch that stops the motor from starting again.
- The motor runs but the shutter does not come down: curtain badly rolled or jammed where it enters the guide rails, a slat out of its guide, faulty brake.
- Manual shutter that rises by itself or refuses to come down: spring tension out of adjustment or a slat rubbing at the top of the guide rails.
This is the most critical emergency for the security of your premises: see roller shutter stuck open and our service for making your shop secure.
Stuck halfway
- A sudden stop, then nothing: the motor’s thermal cut-out, a badly adjusted limit switch, or the obstacle detection system if the shutter has one.
- A stop with rubbing or squeaking: misaligned slat, guide rail bent by an impact, curtain rolling up crooked.
- Shutter tilted, one side lower than the other: a slat out of a guide rail or a broken spring on one side. This is dangerous: nobody should walk underneath.
What does the motor noise tell you?
The noise, or the lack of one, tells you whether the problem is electrical or mechanical. Describe it precisely to the technician on the phone: it is often what lets him bring the right part.
| What you hear | What it usually means |
|---|---|
| Nothing at all | The motor is getting no command or no power: power supply, control, receiver, thermal cut-out. |
| A steady hum, no movement | The motor has power but cannot turn: capacitor, brake, or a mechanical blockage. |
| A click, then nothing | The control circuit reacts, but the motor does not start: relay, brake or motor fault. |
| Rubbing or squeaking | A mechanical problem: a slat catching, a dirty or bent guide rail. |
| A sharp bang, like a snap | A spring or mechanical part has probably broken. Stop using the shutter. |
For a motor that overheats, runs without moving the shutter or stops partway, see our page roller shutter motor not working.
Which cause for which symptom, and who should you call?
This table sums up the most common cases: the symptom, the likely cause, what you can safely do, and the right person to call.
| Symptom | Likely cause | What to do | Who to call |
|---|---|---|---|
| No reaction, no noise | Circuit breaker, power cut, emergency stop | Reset the circuit breaker once, check the emergency stop | The electricity supplier if there is a general power cut, otherwise a roller shutter repairer |
| Remote has no effect, key switch works | Batteries, remote or radio receiver | Change the batteries, try another remote | A repairer: remote or control box not working |
| Stops after several operations, motor hot | The motor’s thermal cut-out | Let it cool before a single new attempt | A repairer if it keeps happening |
| Motor hums, shutter does not move | Capacitor, electromagnetic brake | Stop trying, switch off at the circuit breaker | A repairer: motor repair |
| Shutter stops too high or too low | Limit switches out of adjustment | Do not keep trying | A repairer (adjustment) |
| Bent slats, crooked shutter | A slat out of its guide rail, an impact, wear | Do not operate it, do not walk underneath | A repairer: bent or broken slats |
| Manual shutter very heavy after a bang | Broken spring or spring box | Stop lifting the shutter | A repairer: axle, springs and guide rails |
| Key will not turn or spins freely | Seized or broken lock, jammed bolt | Do not force the key | A repairer: shutter locks |
| Lock forced, slats pushed in | Attempted break-in | Take photos, notify your insurer | A repairer: shutter forced after a break-in |
How the price of each job is set: see our guide to the cost of a roller shutter repair.
Why do manual and motorised shutters not get stuck in the same way?
A manual shutter gets stuck mainly for mechanical reasons; a motorised shutter for electrical reasons as well. Knowing which one you have stops you looking in the wrong place.
- Manual shutter: the weight of the curtain is balanced by spring boxes housed in the axle. Blockages come from the central lock, the side bolts, a tired or broken spring, or dirty guide rails.
- Motorised shutter with a central motor: the motor sits in the middle of the axle, often on wide shutters. It sometimes has a manual override (winch or crank) that lets you raise the shutter if it breaks down.
- Motorised shutter with a tube motor: the motor is inside the axle. Common faults: thermal cut-out, limit switches, capacitor, radio receiver.
What you can do yourself, and what you cannot, is explained in our guide to opening a roller shutter manually.
When does a stuck roller shutter become dangerous?
A shutter becomes dangerous as soon as its weight is no longer under control: it can then drop suddenly. In these situations, keep everyone away and call a technician without delay:
- the shutter comes down by itself or drops in one go when you let go of it;
- the curtain is tilted, slats are hanging down or coming out of the guide rails;
- you heard a sharp bang inside the shutter box;
- the motor is smoking, smells of burning or trips the electrics.
Shutter half raised: never walk underneath. Do not prop it up with an object and do not try to hold it up by hand. Call +33 7 68 20 39 55: a technician answers 24 hours a day.
How can you stop a roller shutter getting stuck again?
Most blockages give warning signs: a slower, noisier shutter, slats rubbing, a motor that heats up quickly. Spotting them early and servicing the shutter regularly avoids a breakdown at the worst moment.
- Keep the guide rails clean and the threshold clear: see our roller shutter maintenance tips.
- Have the shutter checked by a professional, ideally under a maintenance contract.
- In a workplace, motorised shutters must be serviced and inspected periodically: see mandatory maintenance.
Our technicians work throughout Normandy, including in Rouen, Caen, Le Havre and Évreux. All emergencies are covered on our page emergency roller shutter repair.
