Broken spring or shutter too heavy: what should you do first?
Here is how to react without putting yourself in danger.
- Stop lifting the shutter by brute force. Without counterbalancing, the full weight of the curtain bears on your shoulders and on the axle.
- Don’t leave it half-way up. A shutter that is no longer counterbalanced can come down suddenly: nobody should walk under it.
- Cordon off the entrance if the shutter is still partly open, to keep customers and delivery drivers away.
- Note what you heard (a sharp crack, a creaking that grew over time) and call +33 7 68 20 39 55.
What do the spring boxes on a roller shutter do?
Spring boxes counterbalance the weight of the curtain so that a manual shutter can be lifted by hand without excessive effort. They are mounted on the axle, inside the shutter box: when you lower the shutter, the springs tighten and store energy; when you lift it, they release it and lighten the load.
Their setting depends on the real weight of the curtain, and so on its width, its height and the slat profile. A spring that is the wrong size or badly set makes the shutter too heavy, or on the contrary makes it rise on its own. That is why roller shutter spring replacement is not just a matter of fitting a new part: the right spring has to be chosen, then tensioned to the right value.
How can you tell if a shutter spring is worn or broken?
Three signs should alert you: a shutter that has become heavy, a shutter that drops on its own and a sharp crack in the shutter box. The first two point to gradual wear, the last one to a break.
Shutter getting heavier
The spring loses strength over the cycles. Operating the shutter takes a little more effort each month, until one person can no longer manage it.
Sign: it takes two people, or the shutter sticks at chest height.Shutter dropping on its own
Let go at the top or half-way, the shutter comes down by itself. The counterbalancing can no longer hold the weight of the curtain.
Sign: a slow or sudden drop as soon as you let go. A real danger to passers-by.Sharp crack in the shutter box
A clean crack, like a whiplash, usually means a spring has broken.
Sign: a single loud noise, then the shutter is unusable or stuck. See shutter stuck closed.On a shutter with several spring boxes, we recommend replacing them together: they are the same age with the same wear, and a new spring next to a worn one throws the axle off balance.
Why should you never replace a spring yourself?
Because a roller shutter spring stores enough energy to cause serious injury, even with the shutter closed. One handling mistake and the axle turns on the person working on it.
The technician works with proper holding tools, replaces the spring box, sets the tension to the weight of the curtain, then checks that the shutter stays balanced half-way up. To find out what you can safely check yourself, read our guide on opening a roller shutter manually.
What if the axle is bent?
A bent axle has to be replaced: a distorted tube cannot be straightened reliably. It bends after an impact, after being forced with a broken spring or after the curtain has dropped; the shutter then rolls up crooked, rubs in the shutter box and moves in jerks.
Replacing the axle means taking down the curtain and transferring or replacing the spring boxes. It is a longer job, which we plan with you: measurements taken, part ordered if needed, shutter secured in the meantime. On an electric shutter with a tube motor, the motor sits inside the axle: the question then also concerns the motor.
How are bent guide rails repaired?
A slightly bent guide rail is straightened on site; a split, badly twisted or rust-eaten rail is replaced. The guide rails steer the curtain on each side: the slightest distortion makes the slats rub and can push them out of their channel.
- An impact at the bottom of the rail: the most common (bumper, pallet truck, wheelie bin). The shutter always jams at the same point.
- Loose fixings: the rail moves each time the curtain passes. It is refixed into sound support.
- Corrosion: common by the sea, it roughens the surface and eventually eats through the rail.
A bent guide rail often damages the slats running through it: we check them at the same time and, if needed, carry out slat replacement on the ones affected.
Should the axle and guide rails be greased?
Yes, but with the right product and in the right places: it is a maintenance task included in our visits. A suitable lubricant reduces friction in the bearings and on the curtain; on the other hand, thick grease in the guide rails holds dust and forms an abrasive paste.
For your part, just keep the bottom of the guide rails clear and report any new noise. Greasing the axle bearings is done with the shutter box open, close to the springs: it is the technician’s job. Our guide to looking after your roller shutter sets out the recommended routine, and the maintenance contract organises it for you.
How much does roller shutter spring replacement cost?
The price depends on the number of spring boxes, the size of the shutter and access to the shutter box.
Price given on site, after the diagnosis and before any work starts: the technician examines the shutter box, springs, axle and guide rails, then gives you the price; nothing is done without your agreement and, if you decline the work after the diagnosis, only the call-out is charged. Itemised invoice at the end. How the price of a repair is set.
What makes the price vary?
- The part at fault: a simple tension adjustment, a spring box, a guide rail or a complete axle do not take the same time or the same parts.
- The number of spring boxes: a wide shutter has several, which we advise replacing together.
- The size and weight of the curtain: they determine the strength of the springs and the axle section required.
- Access to the shutter box: a recessed box, high up or behind a false ceiling makes the job longer.
- When the work is done: a repair booked during the day avoids the surcharge that applies at night, on Sundays and on bank holidays.
If your manual shutter is operated several times a day, compare with motorising your existing shutter, which takes the strain off the springs.
Where do we work on springs, axles and guide rails?
Throughout Normandy, including:
All our mechanical repairs are on the roller shutter repair page, and the lock or bolts on shutter locks.





