Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Technicians available now · 24/7

Roller shutter control box and remote: fitting, adding, replacing.

An electric roller shutter is operated by a key switch, a push-button control box or a radio remote linked to a receiver. DEPANN'Rideaux fits and replaces these control boxes, adds or copies remotes and reprograms the receiver after a loss, so that a missing remote can no longer open your shop.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

Request a call-out

Quick reply, 7 days a week
What do you need?
Add a photo (optional)

Your details stay confidential.

The motor does the work, but the control is what you touch every day. A key that catches, an extra remote for a new member of staff, an outdoor control unit ripped off the wall, a remote lost along with the shop keys: these situations call for a technician who knows key switches, radio receivers and how to program them. This page sets out the possible controls and what we do. If your control no longer responds at all, the page on a remote or control box not working helps you identify the fault.

What types of control are there for a roller shutter?

There are four main kinds of control: the key switch, the push-button control box, the radio remote and the receiver that links it to the motor. They can be combined to suit your access points and habits. We also fit keypads, which replace or add to the key switch.

Key switch

A unit fitted outside, near the shutter. The key controls raising and lowering, either with a single turn or by holding the key turned.

Use: opening from outside when the shutter is the only way in.

Push-button control box

An indoor control with up, down and stop buttons, sometimes combined with an emergency stop button.

Use: operating from inside, with the shutter in view.

Radio remote

A pocket transmitter with one or more channels. A multi-channel model can operate several shutters.

Use: garages, deliveries, opening without getting out of the vehicle.

Radio receiver

A small unit connected to the motor’s control circuit. It stores the authorised remotes and passes on their commands.

Use: essential for any wireless control.

Key, buttons or remote: which control box should you choose?

The right roller shutter control box depends on where you open from and how many people need to open. The table sums up the points to weigh.

ControlLocationStrengthsGood to know
Key switchOutsideSimple, robust, works without batteriesA lost key means changing the cylinder or the switch
Push-button control boxInsideOperate with the shutter in view, immediate stopCannot be used to open from the street
Radio remoteAnywhere within range of the receiverConvenient, one remote per userBattery to keep an eye on, deletion needed if lost
KeypadOutsideNo keys to hand out, code can be changedCode to change when someone should no longer have access

Many shops combine an outdoor key switch with one or more remotes.

We advise keeping a key switch even with remotes: it still works if a battery is flat or a remote goes missing.

How do you add or copy a remote?

To add a remote, you need a model compatible with your receiver, which is then registered in its memory. A remote bought at random, even one that looks identical, will not work if it does not use the same radio protocol.

  • Compatibility: the technician identifies the receiver and the type of coding before supplying the remote.
  • Fixed code or rolling code: with a fixed code, a remote’s code can be copied. With a rolling code, which changes at every press, the new remote must be registered in the receiver: it is more secure.
  • Receiver memory: each receiver accepts a limited number of remotes. Beyond that, a higher-capacity receiver is needed.
  • Several shutters: a multi-channel remote can operate several shutters if their receivers are compatible.

To prepare the visit, keep a working remote to hand and, if possible, a photo of the receiver when it can be seen without dismantling anything.

What should you do after a remote is lost or stolen?

Have the lost remote deleted from the receiver’s memory as soon as possible: as long as it is registered, it can open your shutter. Call +33 7 68 20 39 55 and tell us how many remotes you still have.

  1. 1DeletionThe technician clears the receiver’s memory, or removes only the lost remote if the model allows it.
  2. 2ReprogrammingThe remotes you have kept are registered again one by one.
  3. 3ReplacementA new remote replaces the one that was lost.
  4. 4TestingEach remote is tested, and the lost remote can no longer operate the shutter.

The same logic applies to a lost key switch key: we change the cylinder or the whole switch. If the loss follows a theft or a break-in, see also our page on a shutter forced after a break-in.

Surface-mounted or flush-mounted control: what is the difference?

A surface-mounted control is fixed onto the face of the wall, whereas a flush-mounted control is set into the wall or shopfront and only shows its front panel. The choice depends mainly on the location.

  • Surface-mounted: quick to fit, with no work in the wall. Suited to indoor use and to replacing an existing unit.
  • Flush-mounted: more discreet and harder to rip out or force. Recommended outdoors, on a shopfront exposed to vandalism.

Outdoors, we fit units designed to withstand the weather, with a protective cover if necessary. By the sea, in Dieppe or Le Havre, salty air makes this choice even more important.

How much does a remote or a control box cost?

The price depends on the type of control, compatibility with your receiver and how it is fitted.

The technician gives you the price on site, after checking the receiver and before any work starts: nothing is done without your agreement. On the phone, the receiver model or a photo helps us bring the right parts; itemised invoice at the end. How the price of a job is set.

What makes the price vary?

  • The type of control: a remote, a key switch, a push-button control box or a keypad do not need the same equipment or fitting time.
  • Receiver compatibility: if your receiver is old, full or incompatible, it has to be replaced before remotes can be added.
  • The number of remotes: to supply, program or re-register after a loss.
  • How it is fitted: a flush-mounted unit or one protected by a cover takes more work than a surface-mounted unit.
  • When the work is done: programming during the day avoids the surcharge that applies at night, on Sundays and on bank holidays.

The control also changes during a motor replacement or when you motorise a manual shutter. If the problem comes from the motor rather than the control, see our motor repair page. All our services are on the roller shutter motors page.

Where do we work on remotes and control boxes?

We fit and reprogram shutter controls all over Normandy, including in:

Google reviews

What our customers say

Reviews are shown in their original language (French).

5.0
★★★★★
“Excellent” · 5 Google reviews
★★★★★
« Intervention rapide et très professionnelle. Dépanneur efficace, ponctuel et honnête sur les tarifs. Porte sectionnelle réparée rapidement et proprement. »
Khalid R.Google review
★★★★★
« Dépannage rapide ! Bon prix, très aimable et accessible. »
Emilie R.Google review
★★★★★
« Le monsieur est un professionnel, le travail est minutieux, je vous le recommande. »
Hassan I.Google review

All customer reviews See our Google profile

Frequently asked questions

Remotes and control boxes: your questions

Will a universal remote work with my shutter?

Only if it is compatible with your receiver’s protocol. Code-copying remotes do not work with rolling-code receivers: the technician checks compatibility before supplying you with a remote.

Can one remote operate several shutters?

Yes, with a multi-channel remote, as long as the receivers of the different shutters are compatible. Each button is then paired with one shutter.

Should I keep a key switch if I have remotes?

It is advisable: the key switch still works if a battery is flat, a remote is lost or the receiver fails.

How can an outdoor control unit be protected against vandalism?

By choosing a flush-mounted or reinforced unit, possibly under a protective cover, placed out of reach of knocks. We advise you on the right model for your shopfront.

How long does it take to program a new remote?

Allow 15 minutes on site on average, testing included. Programming is done during a technician’s visit.

A remote to add or a control box to change?

The technician checks your receiver’s compatibility on site and gives you the price before any work starts.