Why choose a made-to-measure roller shutter rather than a standard model?
Because no two shopfronts have exactly the same dimensions: made to measure roller shutters adapt to your opening, whereas a standard model forces you to adapt the opening to the shutter. In the old town centres of Normandy, openings are rarely square, lintels vary from one building to the next and space for the shutter box is often tight.
A shutter that is too narrow leaves play in the guide rails and makes it easier to rip out. A shutter that is too tall rolls up badly and puts extra load on the axle. A correctly sized shutter, on the other hand, slides without rubbing, locks properly and puts less strain on the motor or the springs. It also lasts longer and breaks down less often.
How do we measure your opening?
The technician takes the measurements on site personally: that is the only way to make sure the shutter is built right. We never start manufacturing on the basis of measurements given over the phone.
- 1Measuring the openingWidth taken at the top, middle and bottom, height taken on the left, centre and right, to spot an opening that is out of square.
- 2Measuring the roll-up spaceHeight available above the opening and depth under the ceiling, which determine the possible size of the axle and the shutter box.
- 3Checking the supportsType and condition of the walls, reveals and lintel, to choose suitable fixings and spot any masonry repairs needed.
- 4Technical surveyPower supply, position of the control box, position of the shop sign, threshold and slope of the floor.
These measurements are also used to choose the type of fitting, face-fixed, between the reveals or under the lintel, as explained on our roller shutter installation page.
Which slats should you choose for your made-to-measure shutter?
The choice of slats depends on the level of protection and visibility you want: solid slats for an opaque closure, micro-perforated slats to keep the shop window visible, tube and link for maximum visibility. Each profile has its own detailed page:
- solid slat shutters: opaque, for stockrooms, garages and exposed premises;
- perforated shutters: the shop window stays lit and visible from the street;
- tube and link grilles: known in France as “cobra” grilles, they let you see the whole interior.
The material matters as much as the profile. Galvanised steel is robust and widely used on shop shutters; aluminium is lighter and does not rust, an advantage by the sea, where salty air attacks metal. Slat materials and thicknesses depend on our suppliers’ models: they are specified on the quote.
Can you choose the colour of your roller shutter?
Yes: the curtain, guide rails and shutter box can be lacquered in a colour from the RAL chart, the European colour reference. A lacquered shutter matches your shopfront, your sign or your brand guidelines, and lacquering adds protection against corrosion.
Lacquering is applied in the workshop, before fitting, which gives a more even and longer-lasting finish than paint applied on site. If your shop is in an area where the town hall regulates the appearance of shopfronts, check with its planning department before choosing the colour. Powder coating is done in a colour from our supplier’s RAL chart; it is priced on the quote, according to the colour chosen.
What are the other components of a made-to-measure roller shutter?
A roller shutter is more than its curtain: the bottom slat, guide rails, axle and shutter box are also sized for your opening.
The bottom slat
This is the reinforced slat at the bottom. It rests on the ground, usually has a seal to limit draughts and water getting in, and carries the lock or bolts on a manual shutter.
Check: that the threshold is level, so the slat closes with no gap.The guide rails
These side channels guide the curtain. Their depth must suit the width of the shutter: too shallow and a slat can come out of the rail; too deep and the curtain rattles in the wind.
Check: that the walls are plumb over their full height.The axle
The curtain rolls up around this axle, carried by end plates or brackets. Its diameter depends on the weight and height of the shutter, and determines the size of the shutter box.
Check: the strength of the support that will take the brackets.The shutter box
It covers and protects the rolled-up axle. Lacquered in the same colour as the curtain, it gives a neater shopfront and shields the mechanism from the weather.
Check: the space available without hiding the shop sign.Can the motor be built in from the start?
Yes, and it is the simplest solution: the motor is chosen according to the actual weight of the curtain and built into the axle at the manufacturing stage. On standard shutters, a tube motor sits inside the axle; on very wide shutters, a central motor is more usual, placed in the middle of the axle, and it can have a manual override by winch or crank.
The control is chosen at the same time: key switch, indoor switch, remote control, or a combination of the three. If you would rather start with a manual shutter, it can still be motorised later, but building the motor in from the start avoids a second visit.
How long does it take to make a made-to-measure roller shutter?
Manufacturing takes 2 to 4 weeks after the quote is approved and the deposit paid (30% deposit when you order, the balance on installation), plus fitting on site: half a day to a full day. It varies with the dimensions, the type of slats and the lacquering, and is stated in writing on the quote. If your current shutter is out of action in the meantime, we secure your premises by making your shop safe.
How much does a made-to-measure roller shutter cost?
The price of a made-to-measure roller shutter depends on its dimensions, the slats and the options chosen: it is set in a written quote, drawn up after the measurements are taken.
Site survey and written quote, with no obligation. The survey is free, and the quote itemises every component before anything is ordered. What determines the price of a new shutter.
What makes the price vary?
- The size of the opening: the wider and taller the curtain, the more slats are needed, and the more the axle and guide rails are reinforced.
- The slat profile: solid slats, micro-perforated slats or tube and link do not cost the same to make.
- The motor: a spring-balanced manual shutter or an electric shutter, with the control of your choice.
- The finishes: RAL powder coating and a cover box are options priced on the quote.
- Supports and access: masonry repairs, a weak lintel or fitting at height make the job longer.
A new shutter is guaranteed for 2 years.
Where do we make and fit made-to-measure shutters?
We measure and fit made-to-measure shutters throughout Normandy, including in Rouen, Caen, Le Havre and Fécamp. Replacing an old shutter? See our page on full roller shutter replacement. To make your new shutter last, consider our maintenance contract.
