Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Technicians available now · 24/7

Gate installation: from the pillars to the first test.

A good gate installation is won or lost before fitting: sound, plumb pillars, a level threshold or track, stops in place and power ready for the motor. DEPANN'Rideaux checks these points during a free site survey, fits your swing, sliding or cantilever gate, then adjusts and commissions it, anywhere in Normandy.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

Request a call-out

Quick reply, 7 days a week
What do you need?
Add a photo (optional)

Your details stay confidential.

What should be checked before a gate installation?

Before any gate installation, four points are checked: the pillars, the ground, the space for opening and the power supply. A fault in any of them sooner or later shows up as a gate that rubs, sags or a motor that strains.

The pillars

They carry the whole weight of a swing gate. Reinforced concrete, filled blockwork or stone: their strength and plumb decide how the hinges are fixed.

Check: cracks, a moving pillar, a different gap at top and bottom.

Ground and threshold

A sliding gate runs on a track that must be laid level on a stable base; a swing gate needs a centre stop and leaf stops.

Check: drive slope, gravel or tarmac, water run-off.

Space available

Swing space for the leaves behind the entrance, or a clear run to the side for a sliding or cantilever gate.

Check: trees, meters, letterbox, parked vehicles.

Power supply

An electric gate needs a cable in protective conduit to the motor, and often a cable to the opposite pillar for the photocells.

Check: electrical starting point, possible trench route.

These checks also help choose the type of gate: see the swing gate, the sliding gate or the cantilever gate.

How does your gate installation work?

Fitting follows a set order: prepare the supports, fix the gate, adjust the mechanics, then commission the motor.

  1. 1Site surveyMeasurements, pillar and ground checks, power supply located. The survey is free.
  2. 2PreparationPillar or threshold repairs if needed, footing for a track or motor, trench and conduit for the cables.
  3. 3FittingHinges grouted in or anchored depending on the pillar, leaves hung and adjusted; or track fixed, gate set on its rollers and guided at the top.
  4. 4AdjustmentLeaf alignment, ground clearance, stops, lock and keeper: the gate must move by hand without tight spots.
  5. 5CommissioningMotor connected, limit switches and remotes programmed, safety devices tested, manual release explained.

Masonry work (pillars, threshold, concrete footing) and electrical work (trench, conduit, motor power supply) are included in the quote: we carry them out ourselves or coordinate them with a partner tradesman, so you deal with a single contact.

Do you need to build new pillars?

Not always: a sound, solid, plumb pillar can take a new swing gate. However, a hollow, cracked pillar, or one too weak for the weight of the leaf, must be reinforced or rebuilt, or the gate will eventually sag. For a sliding gate, the pillars mainly act as a stop and support the top guide and photocells; a cantilever gate can even be fitted without a pillar on the run side, on steel posts.

What preparation does a sliding gate need?

A sliding gate needs a perfectly straight, level track laid on a base that does not move. On a gravel drive, the track is set on a concrete strip footing; on tarmac or paving, we check the base is stable enough. The track must also let water drain: in Normandy, a puddle that freezes in winter or a track clogged with leaves in autumn are common causes of blockage. A cantilever gate has no ground track: it rests on carriages fixed to a footing beside the opening.

Do you need permission for a gate installation?

It depends on the commune: under the local plan (PLU) and depending on the area, fitting a gate or fence may require a prior declaration, and the town hall may set a height or appearance. This is particularly the case near listed monuments, which are plentiful in Normandy’s historic centres. Check with the planning department before ordering; we provide the gate’s dimensions and description for your application.

Do you also install business gates?

Yes: entrances to warehouses, industrial estates, car parks and blocks of flats. These gates, wider and more heavily used, are often sliding or cantilever and motorised for intensive use. Once fitted, an automatic gate at a workplace falls under the mandatory periodic inspections: see mandatory maintenance and our maintenance contract, which also covers gates: the frequency of visits and the points checked are defined in the contract.

How much does gate installation cost?

The price depends on the gate chosen, the condition of the pillars and ground, and the motor: it is set out in a written quote after the site survey.

Site survey free, detailed quote with no obligation. Supply, preparation of supports, fitting, motor and, if you wish, removal of the old gate are listed item by item.

Want a gate built to your measurements? See made-to-measure metal gates. Want to motorise an existing gate? See electric gate motors.

Where do we install gates?

In all five Normandy departments, notably around Caen, Rouen and Fécamp. If your gate breaks down, you call the same number and speak directly to a technician. Our full range is on the metal gates in Normandy page, and a pedestrian gate can be fitted at the same time.

Google reviews

What our customers say

Reviews are shown in their original language (French).

5.0
★★★★★
“Excellent” · 5 Google reviews
★★★★★
« Intervention rapide et très professionnelle. Dépanneur efficace, ponctuel et honnête sur les tarifs. Porte sectionnelle réparée rapidement et proprement. »
Khalid R.Google review
★★★★★
« Dépannage rapide ! Bon prix, très aimable et accessible. »
Emilie R.Google review
★★★★★
« Le monsieur est un professionnel, le travail est minutieux, je vous le recommande. »
Hassan I.Google review

All customer reviews See our Google profile

Frequently asked questions

Gate installation: your questions

How long does it take to fit a gate?

It depends mainly on the preparatory work: pillars to repair, a concrete footing to pour, a trench for the power supply. The length of the job is given during the site survey, then confirmed on the quote, along with the fitting date agreed with you.

Can you fit a gate I bought myself?

Send us the reference and the instructions: the technician checks that the gate and its fixings suit your pillars before offering to fit it.

Do you take away the old gate?

Removal and disposal of the old gate can be included on the quote, alongside fitting the new one.

Can the old hinges or track be reused?

Rarely: a new gate has its own fixing points, and a worn or bent track would wear out the new rollers. During the visit, the technician checks what can be kept, such as a sound pillar or an existing cable conduit.

A new gate to fit?

A technician comes to check your pillars and ground, then gives you a detailed quote, item by item.