Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Practical guide · Prevention rather than repair

Roller shutter maintenance: good habits and warning signs.

Roller shutter maintenance works on two levels: simple tasks you do yourself (cleaning the guide rails, keeping the threshold clear, watching the shutter) and a regular visit from a professional who checks and adjusts the mechanism. Done properly, it makes breakdowns less frequent and avoids blockages at the worst moment.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

Why maintain a roller shutter?

A well-maintained roller shutter gets stuck less often, wears more slowly and stays safe for the people who walk under it. It is a mechanical part that works every day, often twice a day, exposed to rain, dust and sometimes salty sea air.

  • Fewer breakdowns: dirty guide rails or a rubbing slat make the motor strain until it trips its safety cut-out.
  • Lower costs: an adjustment made in time costs less than an emergency replacement of a motor or spring box.
  • Greater safety: a tired spring or a worn motor brake can be detected before it gives way.
  • Premises that close: a shutter that will not come down in the evening leaves a shop exposed until the repairer arrives.

What maintenance can you do yourself?

These tasks are done with the shutter at rest, without special tools and without opening the mechanism. They are enough to prevent a good share of mechanical blockages.

  1. Clean the guide rails. Remove dust, leaves, sand and gravel with a brush, a vacuum cleaner or a damp cloth, along the full height you can reach from the ground.
  2. Keep the threshold clear. Nothing should be under the bottom slat: doormat, A-board, wedge, rubbish.
  3. Wash the curtain with clean or slightly soapy water. Avoid using a pressure washer near the shutter box, the motor and the control boxes.
  4. Rinse more often by the sea: salt speeds up corrosion of the slats and guide rails.
  5. Look after the controls: remote control batteries, a clean and protected key switch, an accessible emergency stop button.
  6. Watch and listen to the shutter when it is working: that is how a fault is first spotted.
Maintenance does not mean dismantling. Never open the shutter box, and never touch the springs, the axle, the motor or the wiring. These jobs are for a professional.

Should you grease a roller shutter?

Not just anyhow, and not just anywhere: badly applied grease blocks more shutters than it frees. Thick grease in the guide rails traps dust and sand, forms an abrasive paste and slows the curtain down.

  • Guide rails: clean them first. If a product is needed, ask your technician which one to use on your model; do not pour on oil or grease at random.
  • Lock: a lubricant made for locks, in a small amount, never thick oil.
  • Springs, axle, bearings, motor, brake: do not touch them. They are lubricated and adjusted during a professional visit, with the shutter box open and the shutter secured.

If in doubt, leave it: a clean, dry shutter works better than a badly greased one.

What visual checks should you make on your roller shutter?

A regular visual check, from the ground and without dismantling anything, picks up most faults before they cause a breakdown. Here is what to look at:

PartWhat you look atWarning sign
Curtain (slats)Alignment, condition of the slatsA slat dented, cracked, rusty or sticking out
Guide railsCleanliness, fixing to the wallA guide rail bent, loose or clogged
Bottom slatContact with the ground, sealShutter no longer touching the ground on one side, seal torn off
OperationSpeed, smoothness, noiseSlower shutter, jerky movement, squeaking, banging
Top and bottom stopsWhere the shutter stopsShutter stopping too high, too low or rising by itself
ControlsRemote, key switch, emergency stopReduced range, damaged or damp control box
Lock and boltsHow the key turns, how far the bolts travelStiff key, bolt not retracting fully

Damaged slat: it can often be replaced on its own, see slat replacement.

How often should a roller shutter be maintained?

The simple tasks are done regularly, as often as dirt builds up; the professional check is done at fixed intervals, more frequently for a heavily used motorised shutter.

TaskWhoRecommended frequency
Watch the shutter while it operatesYouEvery time it opens and closes
Clear the threshold and the bottom of the guide railsYouAs soon as debris builds up
Clean the guide rails and curtainYouRegularly, more often by the sea, in dusty areas or near a busy road
Checking, adjusting and lubricating the mechanismA professionalPeriodically, depending on use; at least every six months for a motorised shutter in a workplace

Shops on the coast, as in Le Havre, Dieppe or Cherbourg, would do well to clean more often: salty air attacks metal. In town centres, in Rouen or Caen, it is mainly dust and street debris that clog the guide rails.

Which signs should worry you?

Any change in the way the shutter behaves is a warning sign: serious breakdowns almost always give notice. Call in a technician if you notice:

  • a slower shutter that strains or stops partway;
  • a new noise: squeaking, rubbing, banging, a motor humming louder;
  • a manual shutter that becomes heavier, or rises or drops by itself;
  • a curtain that tilts or a slat coming out of the guide rails;
  • a motor that heats up quickly or trips its safety cut-out after only a few operations;
  • a remote control that only works at short range.

To interpret a specific symptom, see our guide why a roller shutter gets stuck. If the shutter is already stuck, see our page emergency roller shutter repair.

What does a professional do during a maintenance visit?

The technician checks, adjusts and secures everything you cannot do yourself, then records the work. A DEPANN'Rideaux maintenance visit follows these steps:

  1. 1Testing and listeningFull operating cycles to pick up noises, jerks and stopping faults.
  2. 2Curtain, slats and guide railsChecking alignment, wear and fixings, cleaning the guides.
  3. 3Axle and springsChecking their condition and the balance of the curtain, adjusting the tension if needed, with the shutter secured.
  4. 4Motor and brakeChecking operation, the brake and the limit switches, adjusting the top and bottom stops.
  5. 5Controls and safety devicesRemotes, key switch, emergency stop, manual override if the shutter has one.
  6. 6Lubrication and reportLubricating the points specified by the manufacturer, then a written report and an updated maintenance log.

If a part is worn, you are told about it and given its price before anything is replaced. We work on all brands, manual and motorised shutters alike; see also our motor repair service and repairs to the axle, springs and guide rails.

Is roller shutter maintenance mandatory?

Yes for automatic and semi-automatic shutters installed in a workplace: the regulations require them to be serviced and inspected at least every six months, with an up-to-date maintenance log (French Labour Code, Code du travail, articles R4224-12 and R4224-13). The texts and the cases concerned are explained in our guide mandatory maintenance: what the law says.

Stop worrying about it: the maintenance contract. We schedule the visits, keep the log up to date and let you know before each visit. All the details are on our page roller shutter maintenance contract.

Frequently asked questions

Looking after your roller shutter: your questions

What should you clean a roller shutter’s guide rails with?

With a brush, a vacuum cleaner or a damp cloth, with the shutter at rest. The aim is to remove dust, sand and debris, not to add grease: a clean, dry guide rail is better than a badly greased one.

Can you use a pressure washer on a shutter?

On the curtain, carefully and from a distance, but never aimed at the shutter box, the motor or the control boxes. Water under pressure can get into the electrical parts and wash the lubricant out of the mechanical parts.

Does a manual shutter need professional maintenance?

Yes, even without a motor. Spring boxes tire over time and only a professional can check and adjust their tension safely. The frequency is agreed with the technician according to how the shutter is used.

How much does roller shutter maintenance cost?

The price depends on the type of shutter, whether it is motorised and the number of visits a year: 1 visit a year for a manual shutter, 2 visits a year for a motorised shutter. Any parts are extra; under contract, repairs come with preferential terms, set out in the contract. The annual price is given to you in writing before you sign anything; the options are detailed on our page maintenance contract, and the guide to the cost of a roller shutter repair explains how the price of a repair is set.

What does a roller shutter maintenance log contain?

It records the visits, checks, adjustments and repairs carried out on the shutter, with their dates. In a workplace, it must be kept up to date for automatic and semi-automatic shutters. We fill it in at every visit.

Does your roller shutter need a service?

A technician will advise you on how often it should be maintained and give you the price on site, once he has examined the shutter.