Technicians available now Call-outs across Normandy 24 hours a day, 7 days a week Price given on site, before any work
5.0 on Google
Practical guide · Safety first

How to open a roller shutter manually: what is possible, what is dangerous.

You can open a roller shutter manually in only three cases: a manual shutter that is slightly stiff, a jammed lock or bolt, and a motor fitted with a manual override, used according to the manufacturer’s instructions. Everything else, springs, axle, shutter box or electrics, must be left to a technician.

  • 24/7nights and bank holidays
  • Price given on sitebefore any work
  • All brandsparts in stock

What should you check before touching the shutter?

Before doing anything by hand, rule out the simple causes. These checks need no tools and carry no risk.

  1. Is the shutter’s circuit breaker switched on? Reset it once only; if it trips again, leave it.
  2. Has the emergency stop button been left pressed in?
  3. Does the remote control have fresh batteries? Does the key switch work instead?
  4. Has the motor had time to cool down after several attempts?
  5. Is the shutter straight, with no slat hanging down or coming out of the guide rails? If not, stop there.
Shutter tilted, dropping by itself or after a sharp bang: do nothing, keep people away and call. A spring has probably given way and the curtain is no longer held.

Can you free a roller shutter yourself?

Yes, but only in specific situations, without forcing tools and without opening up the mechanism. The table below sets out what is and is not reasonable.

SituationCan you do it yourself?Limit not to go beyond
Manual shutter that is hard to lift but stays straightYes, with careStop at the slightest unusual resistance
Side bolts that will not releaseYesDo not hit them, do not use a lever
Key that is hard to turnYes, with a product made for locksDo not force it: a key broken off in the cylinder makes everything harder
Central motor broken down, with a manual overrideYes, following the manufacturer’s instructionsNever dismantle the motor or open the shutter box
Tube motor without a manual overrideNoCall a technician
Broken spring, shutter very heavy or droppingNoStop lifting the shutter
Slat out of its guide rail, crooked shutterNoDo not operate it, do not walk underneath
Wiring problem, motor smoking or tripping the electricsNoSwitch off at the circuit breaker and touch nothing else

How do you free a manual shutter that is slightly stiff?

A manual shutter that sticks a little can often be freed by operating it properly, without brute force. Only do this if the curtain is straight and you have not heard any unusual noise.

  1. 1Unlock it fullyKey turned all the way, side bolts fully retracted. A half-engaged bolt is enough to block the shutter.
  2. 2Clear the threshold and the bottom of the guide railsRemove gravel, leaves or anything jammed there, by hand or with a brush, without metal tools.
  3. 3Lift with both hands, in the centreHold the bottom slat by its handles or in the middle and lift in one steady movement, without jerking.
  4. 4Stop at the slightest resistanceIf the shutter catches, tilts or feels much heavier than usual, lower it gently and do not persist.

A manual shutter that suddenly becomes heavy almost always points to a spring problem. That is no longer a blockage to free but a repair to the axle or springs, to be left to a professional.

What should you do if the shutter’s lock or bolts are jammed?

A seized lock calls for patience and the right product, never for forcing the key. What to do:

  • Check the key: a bent or worn key turns badly. Try the spare if you have one.
  • Use a lubricant made for locks, a small amount in the cylinder, then work the key gently. Avoid thick oils, which attract dust.
  • In frosty weather, a lock de-icer can free a cylinder that has frozen.
  • Help the bolts along: as you turn the key, press lightly on the bottom slat to take the load off the side bolts.

If the key spins freely, will not turn at all or the lock has been forced, the mechanism is damaged: see our roller shutter lock service or, after a break-in, the page shutter forced after a break-in.

How do you use the manual override on a central motor?

The manual override lets you raise or lower a motorised shutter during a power cut or a motor failure, but only if it has one and only by following the manufacturer’s instructions. Not every shutter has one, and each model has its own procedure.

  • Check that it exists: on a central motor, it usually takes the form of a winch with a crank handle or a chain control, reachable without dismantling anything. Tube motors, housed in the axle, do not always have one.
  • Read the instructions for your motor or the document you were given at installation. Without instructions, do not guess: call.
  • Switch off the power at the circuit breaker before operating it, if the instructions say so, to prevent the motor starting unexpectedly.
  • Turn slowly and steadily, without extending the crank handle or forcing it, and stop if the resistance suddenly increases.
  • Return the system to its normal position as described in the instructions, then have the motor checked: the original fault has not been fixed.

No instructions, no override. If you do not know whether your shutter has a manual override, a technician can tell you over the phone from a photo of the motor or the shutter box: +33 7 68 20 39 55. See also our page roller shutter motor not working.

What must you never do to free a roller shutter?

Never touch parts under mechanical or electrical tension: that is where serious accidents happen. In practice, never try to:

  • dismantle, release or “re-tension” a spring or spring box;
  • loosen or dismantle the axle, or the end plates or brackets that carry it;
  • open the shutter box (hood) to “see what is jammed”;
  • open the motor housing or work on the wiring, the control box or the receiver;
  • lift the shutter with a lever, a crowbar, a jack or a vehicle;
  • prop a shutter halfway up with an object, or walk underneath it;
  • hit the slats or the guide rails to “unjam” the curtain.

The spring boxes store the energy needed to balance the weight of the curtain. Released all at once, that energy can throw parts out or spin the axle violently. A steel curtain let go without restraint can drop with its full weight.

When should you call a repairer rather than keep trying?

Call as soon as the simple checks have led nowhere or one of these signs appears:

  • the shutter is tilted, hanging or drops by itself;
  • you heard a sharp bang;
  • the motor hums without the shutter moving, overheats or smells of burning;
  • the circuit breaker trips every time you try;
  • the key spins freely or the lock has been forced;
  • the shutter is stuck open and you need to close your premises.

A DEPANN'Rideaux technician answers 24 hours a day, helps you describe the fault and gives you safety advice and an arrival time. The technician gives you the price on site, after the diagnosis and before any work starts: nothing is done without your agreement. Depending on the case, see shutter stuck closed, shutter stuck open or our emergency roller shutter repair in Normandy. To understand what caused the blockage, read our guide why a roller shutter gets stuck.

We work in places such as Rouen, Caen, Le Havre and Cherbourg, by day and by night.

Frequently asked questions

Freeing a shutter yourself: your questions

Can you lift a motorised shutter by hand during a power cut?

Only if it has a manual override, used according to the manufacturer’s instructions. Without one, the motor’s brake holds the curtain: trying to lift it by hand will not work and may damage the mechanism.

How do I know whether my shutter has a manual override?

Check the instructions or the document you were given at installation: they state whether there is a winch, a crank handle or a chain. If in doubt, send a photo of the motor or the shutter box to the technician, who will confirm it.

What product should you use on a seized shutter lock?

A lubricant designed for locks, in a small amount, and a lock de-icer in frosty weather. Avoid grease and thick oils, which hold dust and end up blocking the cylinder.

Why must you never touch a shutter’s springs?

Because they are permanently under high tension to balance the weight of the curtain. Removing or adjusting them requires specific tools and a precise method: a mistake can cause serious injury.

My shutter opened after using the manual override: should I still call?

Yes. The manual override gets round the fault, it does not repair it. Have the motor and the control checked before putting the shutter back into normal use.

Your shutter still will not open?

Do not persist and do not take any risks. A technician answers straight away and tells you when they can arrive; the price is given on site, before any work starts.